3864480 Pulley Question - NCRS Discussion Boards

3864480 Pulley Question

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • R N.
    Expired
    • May 31, 2002
    • 640

    3864480 Pulley Question

    Hi Everyone,

    It appears that I have a water pump pulley on my '66 L-72 W/O PS which is not typical. Mine does not have a p/n on it and it's center section looks like a top hat rather than a cone shape. Is the pulley I have acceptable with regard to judging?

    I'd like some verification to the originals, are they cone shaped? and stamped with a p/n? Are the repos any good or I am better off with a good used one or NOS or keep the one I have?

    Thanks for the input guys.

    Regards,

    Kurt
  • Joe L.
    Beyond Control Poster
    • February 1, 1988
    • 43193

    #2
    Re: 3864480 Pulley Question

    Kurt----

    What it sounds like is that you have a GM #3906656 pulley. This is the 67 pulley which replaced the 66 pulley, GM #3864480, for SERVICE in December, 1966.

    The later pulley is configured differently as you describe. Some of these have p/n's on them and some don't. I don't know why.

    Don't throw the one you have away, though. This is a highly sought-after pulley by "67 guys".
    In Appreciation of John Hinckley

    Comment

    • Joe L.
      Beyond Control Poster
      • February 1, 1988
      • 43193

      #3
      Re: 3864480 Pulley Question

      Kurt----

      What it sounds like is that you have a GM #3906656 pulley. This is the 67 pulley which replaced the 66 pulley, GM #3864480, for SERVICE in December, 1966.

      The later pulley is configured differently as you describe. Some of these have p/n's on them and some don't. I don't know why.

      Don't throw the one you have away, though. This is a highly sought-after pulley by "67 guys".
      In Appreciation of John Hinckley

      Comment

      • R N.
        Expired
        • May 31, 2002
        • 640

        #4
        Re: 3864480 Pulley Question

        Hi Joe,

        Thanks for the info. I'll try to post a picture of what I have tomorrow.

        Bye,

        Kurt

        Comment

        • R N.
          Expired
          • May 31, 2002
          • 640

          #5
          Re: 3864480 Pulley Question

          Hi Joe,

          Thanks for the info. I'll try to post a picture of what I have tomorrow.

          Bye,

          Kurt

          Comment

          • R N.
            Expired
            • May 31, 2002
            • 640

            #6
            Joe Lucia 3906656 Pulley Picture???

            Hi Joe,

            Here's a picture (Clink on the link below) of the pulley I have. Can you tell from this if it is the 3906656 pulley? It's 7-1/8" OD

            Thanks again for your help.

            Regards,
            Kurt




            Comment

            • Joe L.
              Beyond Control Poster
              • February 1, 1988
              • 43193

              #7
              Re: Joe Lucia 3906656 Pulley Picture???

              Kurt----

              Yes, that's exactly what a 3906656 looks like and it's also the correct OD. However, as one small caveat, there are some other GM pullies which look very similar to the 3906656 so I can't be 100% certain. But, I'm about 99% sure.
              In Appreciation of John Hinckley

              Comment

              • R N.
                Expired
                • May 31, 2002
                • 640

                #8
                Now I know what I have...

                Joe,

                Now I know what I have, I only need to find the correct 3864480 pulley that I need. Anybody got an original 3864480 pulley they want to part with?

                Regards,

                Kurt

                Comment

                Working...

                Debug Information

                Searching...Please wait.
                An unexpected error was returned: 'Your submission could not be processed because you have logged in since the previous page was loaded.

                Please push the back button and reload the previous window.'
                An unexpected error was returned: 'Your submission could not be processed because the token has expired.

                Please push the back button and reload the previous window.'
                An internal error has occurred and the module cannot be displayed.
                There are no results that meet this criteria.
                Search Result for "|||"