Code 12, Check Eng Lite, 82 Crossfire ?? - NCRS Discussion Boards

Code 12, Check Eng Lite, 82 Crossfire ??

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Stuart G.
    Expired
    • February 10, 2020
    • 4

    Code 12, Check Eng Lite, 82 Crossfire ??

    Hi to everyone ,new member here.
    Can anyone help,I,ve got 82 crossfire and the check engine light is on, the diagnostic check comes up with code 12 and I cant reset it ,any got ideas. thanks .
  • Rick C.
    Frequent User
    • May 31, 1998
    • 57

    #2
    Re: Code 12, Check Eng Lite, 82 Crossfire ??

    If the ``Test'' terminal is grounded with ignition on and engine not running, the system will enter the diagnostic mode. In the diagnostic mode, the ECM will flash a Code 12 and energize all ECM controlled relays.After flashing code 12 3 times, if there is a trouble code stored, that code will then flash 3 times followed by a code 12 again 3 more times
    Rick Coker
    Indiana Judging Chairman

    Comment

    • Arland D.
      Moderator
      • July 31, 1980
      • 415

      #3
      Re: Code 12, Check Eng Lite, 82 Crossfire ??

      Stuart,

      In other words, if all you are getting is a code 12, everything is fine.

      Comment

      • Edward J.
        Extremely Frequent Poster
        • September 15, 2008
        • 6940

        #4
        Re: Code 12, Check Eng Lite, 82 Crossfire ??

        Stu the old school computer code 12, I believe is also a no tach signal. But the guys above are also correct when the key is on and ALDL is grounded and engine is not running then code 12 is your ready to go, all OK.
        New England chapter member, 63 Convert. 327/340- Chapter/Regional/national Top Flight, 72 coupe- chapter and regional Top Flight.

        Comment

        • Perry M.
          Very Frequent User
          • January 1, 1977
          • 325

          #5
          Re: Code 12, Check Eng Lite, 82 Crossfire ??

          But guys, he said his check engine light is on so there must be another code besides the code 12. I have a similar situation on my 91 ZR-1.

          Comment

          • Arland D.
            Moderator
            • July 31, 1980
            • 415

            #6
            Re: Code 12, Check Eng Lite, 82 Crossfire ??

            Stuart,

            With the ignition key in the 'on' position and the engine stopped, is the 'check engine' light on steady all the time or flashing BEFORE you ground the test terminal??

            Comment

            • Stuart G.
              Expired
              • February 10, 2020
              • 4

              #7
              Re: Code 12, Check Eng Lite, 82 Crossfire ??

              Hi guys, there are no other codes stored but the light is on.

              Comment

              • Stuart G.
                Expired
                • February 10, 2020
                • 4

                #8
                Re: Code 12, Check Eng Lite, 82 Crossfire ??

                Hi . just to make things bad, I have no oil pressure guage working after changing sender and gauge , check pressure with mechanical gauge all ok 45 PSI and the tank empty light is on although theres half a tank of fuel, can these all be connected , bad EMC.

                Comment

                • Arland D.
                  Moderator
                  • July 31, 1980
                  • 415

                  #9
                  Re: Code 12, Check Eng Lite, 82 Crossfire ??

                  Stuart,

                  Now that you have indicated there are other current issues, PM me your email address and I can send you some diagnostic information.

                  Comment

                  • Stuart G.
                    Expired
                    • February 10, 2020
                    • 4

                    #10
                    Re: Code 12, Check Eng Lite, 82 Crossfire ??

                    thanks Arland email address is stuartg-@hotmail.com
                    Originally posted by Arland Dower (3734)
                    Stuart,

                    Now that you have indicated there are other current issues, PM me your email address and I can send you some diagnostic information.

                    Comment

                    Working...

                    Debug Information

                    Searching...Please wait.
                    An unexpected error was returned: 'Your submission could not be processed because you have logged in since the previous page was loaded.

                    Please push the back button and reload the previous window.'
                    An unexpected error was returned: 'Your submission could not be processed because the token has expired.

                    Please push the back button and reload the previous window.'
                    An internal error has occurred and the module cannot be displayed.
                    There are no results that meet this criteria.
                    Search Result for "|||"