Found some in a bag...1967 Bolt & Hardware ID?

[Richard M.]

I got a box of stuff from the owner of the '67 which he saved since 1968. My kinda' guy. Like 14 feet of nos original teal blue seatbelt webbing....and a bunch of original appearing hardware. There' are about 100 pieces altogether, but these below in the photos are most interesting.

I think the 1/4-20 with the toothed washer is for the throttle lever ground strap, and the 4 "FP" 3/8-16's are for the front bumper lower bracket, but the others I'm unsure about.

Thanks,
Rich

[Richard M.]

Re: Found some in a bag...1967 Bolt & Hardware ID?

...more stuff.

[Rich P.]

Re: Found some in a bag...1967 Bolt & Hardware ID?

Richard,

picture #1

toothed washer bolt is small block fuel pump plat to block,
flying f is for later modle ignition/ spark plug shielding (mid 70's up because of the flat washer and not split ring lock washer
CH bolt is 70-up accesorry brackets many locations
1/4-20 j bolt is the same configuration as rear body valance upper bolts but an incorrect headmark must be from some other GM car. I have seen these on Oldsmobies and GTO's

Rich

[Rich P.]

Re: Found some in a bag...1967 Bolt & Hardware ID?

post #1

picture #2

these have been used on rear seat mount for 63-66's and occasionally I have seen them on underdash brackets. They are the longer 1" style and would only have been used on the under dash brackest by mistake and They were supposed to be 3/4" long with a pinched tip. This is also used on some 68-up cars for the front outer bumper bracket to small header supports as well as the headlight actuator housings (the front 4 bolts)

[Rich P.]

Re: Found some in a bag...1967 Bolt & Hardware ID?

Post #1

PICTURE #3

The front lower bumpers to bracket bolts are 7/16-14 thread not 3/8-16. Grade 2 FP bolts like these I have pulled off of 50's and 60's era cars

[Rich P.]

Re: Found some in a bag...1967 Bolt & Hardware ID?

post #1

picture #4

if this a 3/8" hex it is a upper grill rod to header bolts. if it is 1/4" hex head then it's too long for a heater blower motor bolt, if its a 5/16" hex then it would be a courtesy light bracket bolt or lower heater Y duct to heater box bolt

[Rich P.]

Re: Found some in a bag...1967 Bolt & Hardware ID?

Post #2

picture #1

to the left of the picture mostly interior hardware, I see Door sill screws, door pull screws, conv latch to header screws, 1 kick panel screw, the 2 cups with the (most likely L headmaked) 10-24 bolts with 5/16" hex heads are for the top outer corner windshield trim, I see hard to trim and dash hardware. Lots of good stuff. If there is any you specifcally ned identefied post individual pics.

[Rich P.]

Re: Found some in a bag...1967 Bolt & Hardware ID?

Post #2

pic #3

looks like ecklers bought GM hardtop hardware, 2 ferrels and 2 side retainers

[Rich P.]

Re: Found some in a bag...1967 Bolt & Hardware ID?

Post #1

picture #1

addition to first reply since this was a convertablt the bolt with the double circles and star washer could also have been used for the convertable lid latch. The 2 release cables were held in with 4 bolts and clamps This is the same style bolt used there

[Kevin G.]

Re: Found some in a bag...1967 Bolt & Hardware ID?

Richard,
See my recent post! Your first picture has the one I have been searching for!

https://www.forums.ncrs.org/showthre...83958&uid=5286

[Rich P.]

Re: Found some in a bag...1967 Bolt & Hardware ID?

Richard,
See my recent post! Your first picture has the one I have been searching for!

https://www.forums.ncrs.org/showthre...83958&uid=5286

Kevin,

close your trans bracket bolt is 3/8-16 not 5/16-18. Almost but not quite.

Rich

[Kevin G.]

Re: Found some in a bag...1967 Bolt & Hardware ID?

Kevin,

close your trans bracket bolt is 3/8-16 not 5/16-18. Almost but not quite.

Rich

Drat! Thanks Rich!

[Richard M.]

Re: Found some in a bag...1967 Bolt & Hardware ID?

Rich.......all I can say is WOW! That was a awesome response. Thanks very much!

Kevin, yes Rich is right. I replaced those the other day when we put in the transmission and the holes are for 3/8".

Rich

[Richard M.]

Re: Found some in a bag...1967 Bolt & Hardware ID?

Post #2

pic #3

looks like ecklers bought GM hardtop hardware, 2 ferrels and 2 side retainers

Yes...the date on the Ecklers labels are 1988! I had another friend who had lots of GM bags with Ecklers labels at around the same time.

Rich