Am I missing a 68 part? I have a mounting hole but nothing attached - NCRS Discussion Boards

Am I missing a 68 part? I have a mounting hole but nothing attached

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Russ S.
    Expired
    • April 6, 2010
    • 134
    #1

    Am I missing a 68 part? I have a mounting hole but nothing attached

    The attached picture shows what looks like a small mounting hole on the firewall to the left of the bell housing area. My camera was near the starter lookin back and up. I was working on the heater and noticed the threaded hole. It is an A/C car.

    2013-02-19_19-43-52_753.jpg
    Tags: None
      • Top
    • Terry M.
      Beyond Control Poster
      • September 30, 1980
      • 15573
      #2
      Re: Am I missing a 68 part? I have a mounting hole but nothing attached

      Originally posted by Russ Slifer (51592)
      The attached picture shows what looks like a small mounting hole on the firewall to the left of the bell housing area. My camera was near the starter lookin back and up. I was working on the heater and noticed the threaded hole. It is an A/C car.

      [ATTACH=CONFIG]44925[/ATTACH]
      Russ, I am trying not to be a wise a$$, and you have no idea how hard that is, but last time I checked for Corvettes the starter is on the right hand (passenger) side of the car. When referring to left or right it is traditional (and downright confusing) to use the location as if one were sitting in the car -- not looking at it, since the latter can change as one walks around the car. This is one of the reasons you will not (I hope) find the terms left hand or right hand in the early C3 TIM&JGs. We tried our best to refer to passenger and driver side of the car to make a book that is already very confusing just a little less so.
      Terry
        • Top

        Comment

        • Russ S.
          Expired
          • April 6, 2010
          • 134
          #3
          Re: Am I missing a 68 part? I have a mounting hole but nothing attached

          No worries. The mounting hole is on the right side on the fire wall. To help understand the photo i used the term left. Any suggestions on the hole? It doesnt seem to match anything on the inside.
            • Top

            Comment

            • Jeff P.
              Expired
              • October 21, 2011
              • 287
              #4
              Re: Am I missing a 68 part? I have a mounting hole but nothing attached

              Russ check in the assembly manual @ C60 sheet A5, Detail 5 could this be the plate you are seeing ?
                • Top

                Comment

                • Michael D.
                  Expired
                  • June 30, 1996
                  • 536
                  #5
                  Re: Am I missing a 68 part? I have a mounting hole but nothing attached

                  Originally posted by Jeff Piekutowski (53984)
                  Russ check in the assembly manual @ C60 sheet A5, Detail 5 could this be the plate you are seeing ?
                  I agree. Looks AC related to me.
                    • Top

                    Comment

                    • Wayne W.
                      Extremely Frequent Poster
                      • April 30, 1982
                      • 3605
                      #6
                      Re: Am I missing a 68 part? I have a mounting hole but nothing attached

                      Convertible? Dash bracing bars?
                        • Top

                        Comment

                        • Russ S.
                          Expired
                          • April 6, 2010
                          • 134
                          #7
                          Re: Am I missing a 68 part? I have a mounting hole but nothing attached

                          I don't have an assembly manual. I will look for one. thanks
                            • Top

                            Comment

                            • Jeff P.
                              Expired
                              • October 21, 2011
                              • 287
                              #8
                              Re: Am I missing a 68 part? I have a mounting hole but nothing attached

                              Russ a assembly manual will be one of the best tools you can purchase to re-assemble your corvette. Look in the back pages of the Driveline, or on this site at the NCRS Store. www.paragoncorvette.com has them also.
                                • Top

                                Comment

                                Previous template Next
                                Working...

                                Debug Information

                                Searching...Please wait.
                                An unexpected error was returned: 'Your submission could not be processed because you have logged in since the previous page was loaded.

                                Please push the back button and reload the previous window.'
                                An unexpected error was returned: 'Your submission could not be processed because the token has expired.

                                Please push the back button and reload the previous window.'
                                An internal error has occurred and the module cannot be displayed.
                                There are no results that meet this criteria.
                                Search Result for "|||"